Moebius 1/144 Discovery Spacecraft: Part 7

Last time, I finished wiring and lighting the interior of the command sphere, and had it assembled and preshaded.

The final part of the build was to put together all the various cargo pods along the spine of the spacecraft, as well as the dish antennae that featured as a plot device in the film.

By my reckoning 358 parts had to be built into 71 subassemblies for the cargo pods:

Subassemblies for Moebius Discovery cargo modules
Click to enlarge

These assemble, around the spine sections at bottom right above, into ten separate units of triangular cross-section, and one square-section unit that supports the dish antennae. All the units are different, and I had to annotate my instruction sheet to keep them all in the right order, assigning numbers from 1 to 10 as I constructed each one. For ease of painting, I initially left them partially assembled:

Partially assembled cargo modules for Moebius Discovery
Click to enlarge

And once I’d got the base coat and preshading done, I completed each unit, sticking a number on it as I went along.

Completed and preshaded cargo modules for Moebius Discovery
Click to enlarge

I used some more of Aztek Dummy’s rectilinear masks to produce a bit of surface mottling, and a dark grey wash to emphasize the surface detail.

Preshaded cargo modules for Moebius Discovery
Click to enlarge

The small antenna dishes needed a slight modification—the kit parts inaccurately give them each a central spike, but in the “real thing” the central spike was a feature of only the large, central dish:

Reference image for Discovery dish antennae
Click to enlarge

it was easy enough to omit the small central spikes and blank off their locating holes with a suitable small disc of thin styrene sheet (punched out with a leather punch), to reproduce the appearance in the film.

At this point I decided that my final blending coat needed to go on while the individual components were still separate, to ensure good coverage—so I treated the command sphere, the engine compartment, the engine bells, and all the cargo units individually, but with the same mix of paint—two pots of Tamiya flat white, with some German Grey stirred in incrementally until I had the very light grey finish I wanted, and then a few drops of Blue just to nudge it towards a cold white point.

Finally, everything was slid on to the steel spine, and the spinal rods were cemented to the command sphere, the central sleeve, and the engine block—bearing in mind that I’d shortened one of them and it needed to go at the back of the assembly! The final act for the model itself was to connect the command sphere wiring to the battery pack in the engine compartment:

Moebius 1/144 Discovery battery stowage
Click to enlarge

Then I needed to set about getting it properly displayed. The kit comes with three stands, each supported by a steel rod, so I had no worries about their ability to bear the extra weight I’d loaded into the engine compartment and command sphere. There’s a flat tripod for the engine compartment, a broad shallow dish for the command sphere, and a little intermediate cradle to stop the central spine from sagging. I finished these in matt black, except for the support cradles, which were painted to match the model itself.

Moebius 1/144 Discovery display stands
Click to enlarge

It’s not immediately obvious how to position the engine compartment cradle, but a bit of experimentation finds the sweet spot:

Moebius Discovery fit for rear stand
Click to enlarge

The subtle shading of the command sphere panels shows up best when photographed against a neutral grey background:

Moebius 1/144 Discovery shading view 1
Click to enlarge

The rectilinear mottling on the engine compartment is sufficiently subtle to be almost subliminal, which is more or less what I wanted:

Moebius 1/144 Discovery shading view 2
Click to enlarge

And the primary effect of preshading on the cargo modules is to enhance some of surface detail:

Moebius 1/144 Discovery shading view 3
Click to enlarge

Although the kit instructions position the central stand directly under the antenna module, it fits anywhere along the spine. Obviously it needs to be somewhere fairly central, but for me the most aesthetic result was to place it equidistant between the two other stands, slightly behind the antennae.

Here’s the completed model on its display base, with the three stands cemented in position:

Moebius 1/144 Discovery on stand 2
Click to enlarge
Moebius 1/144 Discovery on stand 1
Click to enlarge

The base comes from a UK company called Lasacryl, who make gorgeous custom display cases.

The mission patches that complete the display are from an Etsy seller called Demogorgon.

Demogorgon Discovery patches
Click to enlarge

They’re a good match for the mission patches featured in the film:

Reference images for 2001 Discovery mission badges
Click to enlarge

Here are the engine lights in action:

Moebius 1/144 Discovery engines lit 1
Click to enlarge
Moebius 1/144 Discovery engines lit 2
Click to enlarge

The completed cockpit is difficult to photograph, but you should be able to see my little Frank Poole figure peering out at you from the pilot’s seat:

Moebius 1/144 Discovery cockpit lighting
Click to enlarge

And the pod on its extended platform:

Moebius 1/144 Discovery pod lighting 1
Click to enlarge
Moebius 1/144 Discovery pod lighting 4
Click to enlarge
Moebius 1/144 Discovery pod lighting 5
Click to enlarge

With the extended pod removed, we can peer inside the pod bay:

Moebius 1/144 Discovery Green Strawberry pod bay 1
Click to enlarge
Moebius 1/144 Discovery Green Strawberry pod bay 2
Click to enlarge
Moebius 1/144 Discovery Green Strawberry pod bay 3
Click to enlarge

And the whole thing in its display case:

Moebius 1/144 Discovery in case
Click to enlarge
Moebius 1/144 Discovery in case 2
Click to enlarge

Finally, I couldn’t resist placing my model against a couple of more dramatic backgrounds. First, heading for Jupiter:

Moebius 1/144 Discovery approaching Jupiter
Click to enlarge

And an homage to Peter Hyams’ film, 2010: The Year We Make Contact, in which the abandoned Discovery is found “parked” close to Jupiter’s moon Io, and discoloured by the sulphur erupting from Io’s volcanoes:

Moebius 1/144 Discovery 2010 homage
Click to enlarge

(I’ve composited my Discovery model with images from this random starfield generator, Celestia, and some NASA photographs.)

2 thoughts on “Moebius 1/144 Discovery Spacecraft: Part 7”

  1. That project sure wrapped up well. Looking at that display case I’m thinking that in the interests of displaying models it may be a good thing the designers decided to omit the ship’s radiators even though I still wish they hadn’t.

    1. Glad you liked it.
      Yep, the radiators would have made a deeply unwieldy beast completely unmanageable.

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.